Heat Shrink Tubing Y-Style Molded Shapes for Cable Branches

Release time:

2026-11-18 11:56

The Heat Shrink Tubing range from Dongguan Keyu New Material Technology includes the Y-Style Heat Shrink Molded Shapes shown on this product page. The page describes a molded shape designed to protect cable branches and splits, with a choice of materials for different environments, an optional lip and a glue lined version for waterproofing. It lists the KY/MS-3A/Y-01 and KY/MS-3B/Y-01 models, both described as Y-style cable branch protection tubing that provides mechanical protection and strain relief at the cable splits. For a harness maker, the molded shape is often the part that decides whether a branch survives vibration and handling.

What a Y-Style Molded Shape Does

A Y-style heat shrink shape covers the point where one cable splits into two. A straight tube cannot follow that geometry without wrinkling or leaving a gap, so a molded shape is used to seal and support the branch. The page says the part provides mechanical protection and strain relief for cable splits, and the optional glue lining adds a waterproof seal. A buyer should check the branch angle, the cable diameter range and the length of each leg, because a molded shape is made for a specific geometry. The page does not give a dimension table, so the drawing and the cable sample should be part of the inquiry.

Materials and Compliance

The page says suitable materials can be selected for the use environment, covering military and commercial requirements, and that the product complies with RoHS and REACH. It also says the shape is easy to install and can be supplied with glue for waterproofing. The page does not name the base material, the shrink ratio, the continuous temperature or the dielectric strength, and those values decide whether the part suits an engine bay, a marine harness or an indoor panel. A buyer should request the technical data sheet and a material sample before the qualification, and should confirm the shrink temperature and the installation method.

Models and Sizes

The page lists the KY/MS-3A/Y-01 cable branch protection tube and the KY/MS-3B/Y-01 cable branch moulded sleeve. Both are Y-style parts for cable splits, but the page does not give the size range, the leg length or the cable diameter for either model. A buyer should send the cable construction, the branch angle and the required leg length, and ask the factory to confirm the model and the tooling. A custom molded shape may need a new tool, so the minimum order and the sample lead time should be clarified before the design is fixed. A standard model is faster if it fits the cable.

Installation and Sealing

The page says the part is easy to install and can be waterproof with glue. A heat shrink molded shape usually needs a heat source, a support to hold the branch in position and a controlled shrink to avoid trapping air or overheating the cable. A glue lined version needs enough heat to melt the adhesive without scorching the jacket. A buyer should ask for the recommended shrink temperature, the heating method and the inspection criteria. A sample installation on the actual cable is the practical way to confirm the fit and the seal before a production run.

Applications

The site lists motor, temperature controller and sensor, automobile, electronics, connector terminal, medical, sewage treatment, power and cable, telecom, sports equipment, lighting, railway, shipbuilding, aerospace, gas pipeline, battery and industrial pipe applications. The Y-style shape fits any harness with a branch, from a sensor cable to a battery pack. The same part may not suit an outdoor and an under-hood location, so the material and the glue should be chosen for the environment. A buyer should describe the temperature, the fluid contact and the flexing in the application, and ask for a material recommendation.

About Keyuace and Ordering

Dongguan Keyu New Material Technology Co., Ltd. is based at Building 3, No. 91, Shipai Avenue West, Shipai Town, Dongguan City, Guangdong Province, China. The contact is Mr. Wei on +86 137 1262 9500, the telephone is +86 0769-8137 2186 and the email is sales@keyuace.com. The site covers braided sleeving, heat shrink tubing, connectors and terminals, heat shrink boots, insulation tube, aeration hose, cable marker sleeves and cold shrink tube. An inquiry should state the cable, the branch geometry, the environment, the quantity and the destination, so the factory can recommend a model or a custom tool.

The Y-style heat shrink molded shape is a small part with a clear job: cover a cable branch, hold the split and keep moisture out. Keyuace offers the part in a range of materials, with an optional lip and a glue lined version, alongside a broad heat shrink and sleeving range. A buyer should confirm the dimensions, the material, the shrink condition and the sample before the order, and should install a sample on the real cable. With those checks, the molded shape can be matched to the harness rather than chosen from a picture.