Application OF Fiberglass Tube

Release time:

2025-04-16 10:31

Analysis of application cases on why some household appliances or electronic appliances use fiberglass sleeves:

The application of glass fiber tubes is very extensive, ranging from home wiring harnesses and household appliances to aerospace.

 

1.Applied to lighting downlights

 

  • A good lighting downlight may be used with the building until it is demolished, so the insulation protection of many downlights is very important. The voltage level of commonly used downlights is less than 300V, and the operating temperature is not high. The insulation layer of the wire harness itself basically meets the insulation conditions, and it is okay not to use additional insulation protection, but its service life is limited. After 5 years, the downlight harness is exposed on the surface and is prone to aging and corrosion. In the long run, it is easy to cause accidents. People can use heat shrink tubing for protection. Heat shrink tubing is cheap and has relatively good insulation and sealing protection properties. However, heat shrink tubing needs to be heated and shrunk, and its shrinking temperature will directly damage the insulation layer of the downlight harness itself. In this way, non-shrinking sleeves (such as fiberglass tubes) have become the choice of downlight insulation protection. 

 

  • Compared with heat shrink tube, this fiberglass sleeve has become the first choice. The parameters of the fiberglass tube are excellent, such as pressure resistance, high temperature resistance, and corrosion resistance. Putting the fiberglass tube in the downlight wiring harness can well protect the downlight wiring harness and extend the service life of the downlight.

 

 

 

 

 

 

 

 

2.In this section, the editor introduces the application of Fiberglass Sleeving in toroidal transformers

 

Toroidal transformers have good output characteristics and anti-interference capabilities, and are widely used in computers, medical equipment, telecommunications, instruments, and lighting.

 

The traditional toroidal transformer standard power transformer product series has a capacity of 8 to 1500VA, a small voltage regulation rate, and a full-load operating temperature rise of only 40°C. It allows short-term overload operation and is suitable for high-demand applications. Class B (130°C) polyester film insulation is used between the primary and secondary windings, and at least three layers of insulation tape are required to withstand an AC 4000V, 1min withstand voltage test. With the advancement of technology and the update of relevant standards, insulation tapes have been replaced by glass fiber tubes. Nowadays, toroidal transformers on the market mostly use glass fiber tubes for insulation protection, and most of them are glass fiber tubes with a withstand voltage of 4KV. Among them, glass fiber tubes with inner fiber and outer rubber and glass fiber tubes with inner rubber and outer fiber are more commonly used.

 

3.The car starter uses three parts to realize the entire starting process.

The DC motor introduces current from the battery and makes the starter drive gear produce mechanical movement; the transmission mechanism meshes the drive gear into the flywheel ring gear, and can automatically disengage after the engine starts;

The on and off of the starter circuit is controlled by an electromagnetic switch. Among them, the motor is the main component inside the starter. The car starter is a valuable part in the car and will not be easily damaged, but in order to extend the service life of the starter, the protection of the car starter and the proper use method are also necessary.

The wiring harness in the car starter is one of the parts that are prone to corrosion and aging damage, so it is particularly important to protect the starter wiring harness.

 

 

Glass fiber tubes have become the first choice for insulation protection of car starter wiring harnesses due to their self-extinguishing, soft, arc, corona, wear and voltage resistance, and corrosion and aging resistance.

 

In order to protect the environment, it is stipulated that all materials of the starter do not contain substances such as asbestos and metal cadmium. The glass fiber tube meets the RoHS environmental protection standards and is fully in line with the application of the automotive industry.

 

 

4.Fiberglass tubes are widely used, and they are also widely used in automobiles. For example, fiberglass tubes are used in the engine coils of new energy vehicles, fiberglass tubes are used in the battery packs of new energy vehicles, and fiberglass is used in the wiring harnesses of automobiles. Fiberglass tubes are used in automobile oxygen sensors.

 

Pure electric new energy vehicles no longer have exhaust pipes, but hybrid new energy vehicles still have exhaust pipes. Automobile oxygen sensors are key feedback sensors in the electronic fuel injection engine control system. They are key parts for controlling automobile exhaust emissions, reducing automobile pollution to the environment, and improving the fuel combustion quality of automobile engines. Oxygen sensors are installed on the engine exhaust pipe. Once the oxygen sensor fails, the computer of the electronic fuel injection system will not be able to obtain information about the oxygen concentration in the exhaust pipe, and thus cannot perform feedback control on the air-fuel ratio, which will increase the engine fuel consumption and exhaust pollution, and the engine will have unstable idle speed, misfire, surging and other fault phenomena. The ceramic of the oxygen sensor is hard and brittle. It may break and fail if it is hit with a hard object or blown with a strong airflow.

 

 

 

 

The protection requirements of automotive oxygen sensors need to improve resistance to degradation and enhance air permeability. At the same time, they need to be resistant to high temperatures and corrosion. The glass fiber tube is made of alkali-free glass fiber yarn woven with resin and then treated at high temperatures. The glass fiber tube used in automotive oxygen sensors adopts the horizontal weaving method and is the first choice for insulation protection.

 

5.First of all, the new energy vehicle motor has a high temperature resistance requirement, and also requires a certain degree of wear resistance, cutting resistance and mechanical toughness. Glass fiber tubes have become the first choice for insulating sleeves for new energy vehicle motors. New energy vehicle motors will use a large number of 1.5KV glass fiber sleeves, 4KV glass fiber sleeves, and high-temperature resistant silicone rubber heat shrink tubes, among which the highest temperature-resistant fixed-weave tubes are also used in large quantities. New energy vehicle wiring harnesses will also use a small part of glass fiber tubes to play an insulating and protective role.

Requirements for glass fiber tubes for new energy vehicles:

Environmental protection is the primary standard for new energy vehicles, followed by the flame retardant standard of glass fiber tubes, which generally need to reach V0 flame retardant level.

 

 

6 .During the operation of the motor, there are usually wiring harnesses and motor connections. The wires commonly used in motors on the market are high-temperature resistant wires, which are generally resistant to temperatures above 125°C or 150°C. Although the motor harness uses high-temperature resistant wires, the loss and corrosion are still serious in the long-term high-temperature and vibration operating environment. The motor harness is often covered with a glass fiber tube, and some even directly use high-temperature resistant wires made of glass fiber. The glass fiber tube is moisture-proof, oil-proof, and anti-weather aging. Anti-pollution, extend the service life of the equipment, silicone rubber glass fiber tube has strong chemical stability, silicone does not react to oil, water, acid, alkali and other substances, within 260°C, it can be used for a long time without aging, and the service life in the natural environment can reach decades, which can maximize the protection of pipes, cables and equipment in these occasions, greatly extending their service life.

 

 

 

7.Whether it is a small fan motor or a medium-sized automobile motor, there will be more or less coils, and fiberglass tubes can be seen in the coils. So what is the role of fiberglass tubes?

 

Our first reaction is insulation and protection. There will be wires in the coils. Covering the wires in the motor with fiberglass tubes can increase the insulation performance of the wires. At the same time, the temperature resistance of fiberglass tubes is higher than that of general wires and cables.

 

In fact, the fiberglass tubes in the motor coils have other uses besides insulation, heat resistance, and wear resistance. That is to play a fixing role. The fiberglass tube is wrapped around the middle and periphery of the coil, and the most intuitive role is fixing. Fixing the coil: ensuring that the coil or magnetic sheet does not move due to high-speed operation; fixing the wire: putting a fiberglass tube on the outer jacket of the wire and then bundling it makes the wire easier to fix. The reason for choosing fiberglass tubes is mainly because the fiberglass tubes have higher pressure resistance and temperature resistance.

 

In addition to fiberglass tubes, silicone rubber heat shrink tubes are also used for insulation protection at wire joints.

 

 

 

8.The most widely used fiberglass tubes in the shipbuilding field are fiberglass tubes with inner fiber and outer rubber and inner rubber outer wire.

 

Fiberglass tubes are mainly used in high temperature areas of ships, cables in heating areas, fluid pipelines, rolling mill cables, oil pipes, sawing cables, generator sets, electrical voltage equipment, large buildings, ship wiring harnesses and exhaust pipes.     The main certifications for fiberglass tubes for ships are SGS environmental certification and UL flame retardant certification. Products with higher environmental protection and flame retardant performance are more conducive to export. The main characteristics of fiberglass tubes for ships are: high temperature resistance, thermal insulation, flame retardant, electrical insulation, chemical stability, weather aging resistance, cold resistance, water resistance, oil resistance, ozone resistance, voltage resistance, arc resistance, corona resistance, etc., especially safety and environmental protection performance, which is the best alternative to hazardous products such as asbestos.

 

Glass fiber tubes for ships are moisture-proof, oil-proof, weather-proof, and pollution-proof, and can extend the service life of ship equipment. Silicone rubber glass fiber tubes have strong chemical stability. Silicone does not react to oil, water, acid, alkali and other substances. They can be used for a long time without aging within 200°C. The service life in natural environment can reach several decades, which can maximize the protection of pipes, cables and equipment in these occasions, greatly extending the service life of ships. According to Interlec, a European distributor, double-insulated glass fiber tubes that can replace molded plastic insulation in the armature shaft of small motors may have a significant impact, and it can save the assembly cost of the motor. This double-insulated tube-glass fiber tube was developed by Polygon in Indiana, USA.

 

According to reports, the insulating tube is permanently pressed into the shaft, avoiding the disadvantages of high cost of traditional shaft insulation and long time spent on insulation bonding, while simplifying the process, reducing energy consumption, and improving production efficiency. The insulating tube is woven from glass fibers and then impregnated with epoxy resin or other resins. The material has low water absorption and can be used in humid environments for a long time, so it can be used reliably in pumps, wet vacuum cleaners and lawn mowers. It can also be used as a material for the pulleys of washing machines, so as to avoid static electricity generated by the pulleys and affect the performance of electronic controls.

 

This fiberglass tubular structure has a large torque when the motor is driven in both directions, which is impossible to achieve with ordinary wire-wound structures.

 

 

9.The heating plate of the induction cooker generates an alternating magnetic field through the components of the electronic circuit board. When the bottom of the iron-containing pot is placed on the stove, the pot cuts the alternating magnetic field lines and generates alternating eddy currents in the metal part at the bottom of the pot. The eddy currents make the iron molecules of the pot move irregularly at high speed, and the molecules collide and rub against each other to generate heat energy. It has the advantages of fast heating, high thermal efficiency, no open flame, no smoke, no harmful gas, no heat radiation to the surrounding environment, small size, good safety and beautiful appearance. The glass fiber tube is made of glass fiber filaments woven into a tube and coated with resin at high temperature. It can be divided into high-temperature resistant fixed-weave tubes, silicone resin glass fiber tubes and high-pressure resistant silicone rubber glass fiber tubes.

 

The power of the induction cooker varies, and the diameter size of the heating plate is also different. Generally speaking, the maximum temperature of an 1800W induction cooker can reach 270 degrees. If it is a dry pot, it will burn the pot red in about 70 seconds. The panel can withstand a temperature of 650 degrees, but it will not actually reach this temperature. The heating plate of the induction cooker will have a power cord. For safety and relevant regulations, it is necessary to use an insulating sleeve for protection. The paint is on the wire coil. If the wire coil is of poor quality, the paint will fall off when it is hot, causing a short circuit and easily causing a pipe explosion. The glass fiber tube has a temperature resistance of more than 200°C and a high voltage resistance level. It is the first choice for insulation protection of the wiring harness of the induction cooker heating plate.

 

 

 

 

10.Application of glass fiber tube in thermistor.

 

First, let's understand what thermistor is and why thermistor uses glass fiber tube.

Thermistor is an electrical component whose resistance value can change with temperature. It has the functions of controlling temperature, measuring temperature and compensating temperature. It is often used in batteries. Electronic thermometers, water dispensers, electric kettles and other electrical appliances. For example, there is an NTC thermistor in the rice cooker. When the rice is cooked, it will jump to the insulation function. This is because the thermistor measures its temperature and controls the temperature. The working temperature of the thermistor is high and varies greatly. The normal temperature device is suitable for -55℃~315℃. When operating in a high temperature environment, the temperature of the connecting wire must reach about 200 degrees Celsius. To insulate the thermistor, ordinary heat shrink tubes are not enough. Glass fiber tubes are one of the best choices.

 

The temperature range of glass fiber tube is between -40℃ and 200℃. It is made of alkali-free glass fiber woven into a tube, coated with silicone resin, and then treated with high temperature. It is flame retardant, environmentally friendly, heat-insulating and insulating, and is a good partner for thermistor protection.

 

 

 

11.Fiberglass tubes are made of fiberglass woven into tubes, impregnated with silicone resin, and then treated at high temperature.

 

Here is an introduction to the use of fiberglass tubes in pizza ovens: Pizza ovens are mainly used for baking pizza. The general maximum operating temperature is about 200 degrees Celsius. The part involving electricity will naturally have wire harnesses, which requires fiberglass tubes for insulation protection. The reason for choosing fiberglass tubes is that fiberglass tubes can withstand high temperatures above 200°C, and at the same time have a high voltage resistance and are wear-resistant, making them the first choice for high-temperature harness insulation protection.

 

 

 

12.Application of glass fiber tube in air conditioner wiring harness.

 

Glass fiber tube is woven from glass fiber, has high heat resistance, excellent mechanical properties, cut resistance, corrosion resistance, can effectively protect the wiring harness and extend the service life of the equipment. There are different types of glass fiber tubes used in household appliances, including yellow wax tube, fixed tube, self-extinguishing tube, inner fiber and outer rubber glass fiber tube, etc. The most commonly used in air conditioners are silicone glass fiber tubes, which are woven from alkali-free glass fibers into a tube and then coated with silicone resin and then treated at high temperature. It has good dielectric properties and good softness, flame retardancy and temperature resistance.

 

Glass fiber protective sleeves are widely used for heat insulation and insulation of motors, household appliances, electric heating equipment, electronic devices and bundled wires. Air conditioning wiring harnesses are mostly air conditioning outdoor unit wiring harnesses, which are often exposed to the outdoors, wind and rain, and are very prone to corrosion, especially the heat resistance of the bundled wires themselves is limited, generally around 100°C, so the air conditioning bundled wiring harnesses are often covered with fiberglass tubes for further protection and to extend the service life of the air conditioning outdoor unit.

 

 

 

 

 

 

Dongguan Keyu New Material Technology Co., Ltd. welcomes customers to inquire:

mobile phone: +(86)13580987327, +(86)18676352059

Phone: +(86)-0769-81372186

Fax: +(86)-0769-81372885

E-mail: Joany150138@keyuace.com

Net1: http//keyuace.1688.com

Net2: www.keyuace.com