(二) High temperature resistant and flame-retardant insulation polyimide PI sleeve
Release time:
2025-04-10 10:39
四、The excellent performance of polyimide PI
(1) Thermal stability performance: Polyimide has excellent resistance to low and high temperatures, and aromatic polyimides generally only decompose under conditions exceeding 500 ℃. Moreover, polyimides synthesized by polymerization of dianhydride with biphenyl as the main structure and p-phenylenediamine only decompose at temperatures exceeding 600 ℃, making them one of the most thermally stable polymers currently known. Experimental studies have shown that the vast majority of PI films that undergo solidification during heating can be used at temperatures above 300 ℃, and a few models of PI can even work normally for hundreds of hours at 380 ℃. At the same time, polyimide also has excellent low-temperature resistance. Even when placed in liquid helium at -269 ℃, the toughness of polyimide is well maintained and it is not easily brittle. The thermal expansion coefficient of polyimide is low. By adjusting the proportion and composition of the synthesized polyimide monomers and adjusting the production process of polyimide, its thermal expansion coefficient can be controlled.
(2) Mechanical properties: Benzene based PI films have a tensile strength of over 170 MPa and a tensile modulus of 3-4 GPa. For example, DuPont's Kapton type films maintain a tensile strength of over 250 MPa. The PI film with biphenyl structure type has a better molecular chain arrangement and ordered structure, with a tensile strength of up to 400 MPa. For example, the tensile strength of Ube's Upilex film can reach 530 MPa. The tensile modulus of polyimide fibers of copolymer type is only slightly lower than that of carbon fibers. In addition, they can maintain excellent wear resistance, friction reduction, and mechanical properties at both high and low temperatures.
(3) Electrical properties: Polyimide has excellent insulation properties and typically has a volume resistivity of around 1018 Ω· cm. It is often used as a packaging barrier material in microelectronic devices. Polyimide, as a material with an insulation level of H, has a low dielectric constant and dielectric loss. The Dk value of unmodified polyimide film is approximately around 3.5, and can be reduced to below 2.0 through different methods of modification synthesis. The dielectric loss of polyimide film at low frequencies is below 0.001. Many properties of polyimide film can be relatively stable in a large temperature and frequency range.
(4) Chemical stability: Thermosetting polyimide films have excellent resistance to dilute acid corrosion, hydrophobicity, organic solvent erosion, and oil resistance. Some fluorinated polyimides and aliphatic polyimides can dissolve in commonly used solvents such as acetone, chloroform, and tetrahydrofuran. Under the action of strong alkali, the imide group with a five membered ring structure is very prone to hydrolysis, so alkali can corrode polyimide. However, due to the characteristic of polyimide, we can recycle it. Polyimide film is hydrolyzed by alkaline water, and the recyclability of diamine and dianhydride monomers is about 80% to 90%. In addition, polyimide is not resistant to concentrated acid.
(5) Transparency: Due to the charge transfer of polyimide, the surface of PI film is mostly yellow in color. Because the - CF3 group and fatty diamine have strong electron withdrawing properties, when they are added to the dianhydride monomer, the fatty tetra anhydride can change the color of the PI film. This is because these measures reduce the charge transfer between electrons.
(6) Other properties: Polyimide has excellent radiation resistance, and even after high-intensity radiation, its various properties do not undergo significant changes.

五、 Application of Polyimide PI
Due to the performance and synthetic chemistry characteristics of polyimide, it is difficult to find such a wide range of applications among numerous polymers, and it has demonstrated outstanding performance in every aspect.
1. Film: One of the earliest products of polyimide, used for slot insulation and cable wrapping materials in motors. Transparent polyimide film can be used as a flexible solar cell substrate.
2. Coatings: Used as insulation paint for electromagnetic wires or as high-temperature resistant coatings.
3. Advanced composite materials: used for aerospace, aircraft, and rocket components. It is one of the most heat-resistant structural materials. For example, the supersonic aircraft program in the United States is designed with a speed of 2.4M, a surface temperature of 177 ℃ during flight, and a required service life of 60000h. It has been reported that 50% of the structural materials used are carbon fiber reinforced composite materials based on thermoplastic polyimide resin, with a usage of approximately 30t per aircraft.
4. Fiber: Its elastic modulus is second only to carbon fiber, and it is used as a filtering material for high-temperature media and radioactive substances, as well as bulletproof and fireproof fabrics.
5. Foam plastic: used as high temperature resistant and heat insulating material.
6. Engineering plastics: There are thermosetting and thermoplastic types, and thermoplastic types can be molded by compression molding, injection molding, or transfer molding. Mainly used for lubrication, sealing, insulation, and structural materials. Guangcheng polyimide materials have begun to be applied in mechanical components such as compressor rotors, piston rings, and special pump seals.
7. Adhesive: Used as a high-temperature structural adhesive. Guangcheng polyimide adhesive has been produced as a high insulation potting material for electronic components.
8. Separation membrane: used for the separation of various gases, such as hydrogen/nitrogen, nitrogen/oxygen, carbon dioxide/nitrogen, or methane, to remove moisture from air hydrocarbon feed gases and alcohols. It can also be used as a pervaporation membrane and ultrafiltration membrane. Due to its heat resistance and resistance to organic solvents, polyimide plays a particularly important role in the separation of organic gases and liquids.
9. Photoresist: There are negative and positive photoresist, and the resolution can reach sub micron level. When combined with pigments or dyes, it can be used for color filter films, greatly simplifying the processing steps.
10. Application in microelectronic devices: used as a dielectric layer for interlayer insulation, and as a buffer layer to reduce stress and improve yield. As a protective layer, it can reduce the impact of the environment on the device and also act as a shield for alpha particles, reducing or eliminating soft errors in the device.
11. Alignment agents for liquid crystal displays: Polyimide plays a very important role in the alignment agent materials for TN-LCD, STN-LCD, TFT-LCD, and future ferroelectric liquid crystal displays.
12. Electro optical materials: used as passive or active waveguide materials, optical switch materials, etc. Fluorinated polyimides are transparent in the communication wavelength range, and using polyimide as a chromophore matrix can improve the stability of the material.
13.Moisture sensitive materials: The principle of linear expansion due to moisture absorption can be used to make humidity sensors.

六、New directions for the development of polyimide PI: lightweight, low-temperature, low dielectric constant, transparency, solubility, low expansion, etc
Direction 1: Low temperature synthesis of polyimide PI: In general, PI is usually formed by the reaction of diamine and dianhydride to produce its prepolymer - polyamic acid (PAA), which must be imidized at high temperature (>300 ℃), which limits its application in certain fields. Meanwhile, during the high-temperature imidization of PAA solution to synthesize PI, volatile by-products are easily generated and difficult to store and transport. Therefore, it is necessary to study the synthesis of PI at low temperatures. The current improvement methods include: 1) one-step method; 2) Molecular design; 3) Add low-temperature curing agent.
Direction 2: Thin, Light, and Uniform Film: In order to meet the design requirements of downstream applications for light, thin, and high reliability, polyimide PI films are developing towards thinning, which puts higher demands on their thickness uniformity, surface roughness, and other properties. The improvement of key performance of PI film not only depends on the molecular structure design of resin, but also on the advancement of film forming technology. At present, the preparation process of PI film mainly includes: 1. Immersion method; 2. Casting method; 3. Dual axis orientation method. With the increasing demand for device weight reduction, thinning, and functionalization in industries such as aerospace and electronics, ultra-thin technology is an important trend in the development of PI thin films. According to the thickness (d), PI films can generally be divided into ultra-thin films (d ≤ 8 μ m), conventional films (8 μ m < d ≤ 50 μ m, common film thicknesses include 12.5, 25, and 50 μ m), thick films (50 μ m < d ≤ 125 μ m, common thicknesses are 75 and 125 μ m), and ultra-thin films (d>125 μ m). At present, the main methods for preparing ultra-thin PI films are soluble PI resin method and blow molding method.
Soluble polyimide resin method: Traditional PI is usually insoluble and non melting, so only its soluble precursor PAA solution can be used for film preparation. Soluble PI resin is obtained by polymerizing dianhydride or diamine monomers with large substituents, flexible groups, or asymmetric and isomeric structures in their molecular structure. The substituents or asymmetric structure can effectively reduce the strong interactions within or between PI molecular chains, increase the free volume between molecules, and facilitate solvent penetration and dissolution. Unlike using PAA resin solution to prepare PI film, this process first directly produces high molecular weight organic soluble PI resin, then dissolves it in DMAc to prepare a PI solution with suitable process viscosity. Finally, the solution is cast, cured, and biaxially stretched on a steel strip to prepare PI film.
Blow molding method: The technology for preparing universal polymer films by blow molding is already mature, and the film thickness can be easily adjusted by changing parameters such as hot air flow velocity. This device differs from the traditional blow molding method in the process of preparing polymer films, as the film is blow molded from top to bottom. The difficulty of this process lies in the transformation of polymer from solution to bubbles, as well as the process of bubbles forming a thin film through a pressure roller. But this process can directly use commercial polyamide acid solution or PI solution for film preparation, and minimizes physical contact between the film and other substrates to the greatest extent possible; Rolls are easier to perform surface polishing treatment and achieve uniform heating compared to steel strips, and can produce PI ultra-thin films with high strength and high heat stability.
Direction 3: Low dielectric constant materials: With the rapid development of science and technology, the trend of integrated circuit industry towards low dimensional, large-scale, and even ultra large scale integration is becoming increasingly evident. When the size of electronic components is reduced to a certain scale, the inductance capacitance effect between wiring gradually increases, and the mutual influence of wire currents makes the signal delay phenomenon very prominent, resulting in an increase in signal delay time. The delay time is directly proportional to the dielectric constant of the interlayer insulating material. A higher signal transmission speed requires the dielectric constant of the interlayer insulation material to be reduced to 2.0-2.5 (usually the dielectric constant of PI is 3.0-3.5). Therefore, in the context of the deepening development of ultra large scale integrated circuits, reducing the dielectric constant of interlayer materials has become an important means to reduce signal delay time. At present, there are four methods to reduce the dielectric constant of PI thin films: 1. Fluorine atom doping; 2. Fluorine free/fluorinated copolymers; 3. Structured with siloxane branched chains; 4. Porous structure membrane
1. Fluorine atom doping: Fluorine atoms have strong electronegativity and can reduce the electronic and ionic polarizability of polyimide molecules, achieving the goal of reducing the dielectric constant. At the same time, the introduction of fluorine atoms reduces the regularity of the molecular chain, making the stacking of polymer chains more irregular, increasing the intermolecular gaps and reducing the dielectric constant.
2. Fluorine free/fluorinated copolymers: Introducing aliphatic copolymer units can effectively reduce the dielectric constant. Lipid ring units also have lower molar polarizability and can disrupt the planarity of molecular chains, while simultaneously suppressing charge transfer and tight stacking of molecular chains, reducing the dielectric constant; Meanwhile, due to the small dipole polarization ability of C-F bonds and their ability to increase intermolecular steric hindrance, the introduction of C-F bonds can effectively reduce the dielectric constant. If a bulky trifluoromethyl group is introduced, it can prevent the tight packing of polymer chains, effectively reduce the intermolecular charge transfer of highly polarized dianhydride units, and further increase the free volume fraction of the polymer, achieving the goal of reducing the dielectric constant.
3. Siloxanes containing branched structures: Cage like molecules - Polysilsesquioxanes (POSS) have advantages such as uniform pore size, high thermal stability, and good dispersibility. The functional groups attached to the vertices of the POSS cage shaped pore structure can be dispersed to a certain extent into the polyimide matrix after surface chemical modifications such as polymerization, grafting, and surface bonding, forming a low dielectric constant composite film with a porous structure.
4. Porous structural membrane: because the dielectric constant of air is 1, it is an effective way to obtain low dielectric polyimide materials by introducing a large number of evenly dispersed pore structures into the polyimide to improve the volume ratio of air therein and form porous foam materials. At present, the main methods for preparing porous polyimide materials include thermal degradation, chemical solvent method, and introducing hybrid materials with nanoporous structures.
Direction 4: Transparent PI: The color of organic compounds is due to their absorption of specific wavelengths of visible light (400-700 nm) and reflection of the remaining wavelengths, which are perceived by the human eye. The absorption in the visible light range is the reason for the coloring of aromatic polyimides. For aromatic polyimides, the chromophores that cause light absorption can include the following: a) two carboxyl groups on the imine ring; b) Phenyl adjacent to the imine ring; c) The functional groups contained in the residual groups of diamine and dianhydride. Due to the strong intermolecular and intramolecular interactions in the molecular structure of polyimide, charge transfer complexes (CTCs) are easily formed between electron donors (diamines) and electron acceptors (diamines), and the formation of CTCs is the intrinsic reason for the material's absorption of light.
To prepare colorless and transparent polyimide, it is necessary to reduce the formation of CTC at the molecular level. The currently widely used methods mainly include: 1. Using monomers with side groups or asymmetric structures, the presence of side groups and asymmetric structures can also hinder the flow of electrons and reduce collinearity; 2. Introducing fluorinated substituents into the molecular structure of polyimide, utilizing the electronegativity of fluorine atoms, can break the conjugation of electron clouds and suppress the formation of CTCs; 3. Use cycloaliphatic dianhydride or diamine monomers to reduce the content of aromatic structures in the polyimide molecular structure.

Polyimide (PI) is an organic polymer material with outstanding comprehensive performance, known as "one of the most promising engineering plastics of the 21st century". The material has a wide temperature range and can work for a long time in an environment of -200~300 ℃, and can withstand high temperatures above 400 ℃ for a short period of time. Currently, polyimide has been widely used in aerospace, shipbuilding, semiconductor, electronics industry, nanomaterials, flexible displays, lasers and other fields. According to the different forms of specific products, the application direction of polyimide can be subdivided into PI foam, PI film, PI fiber, PI matrix composites, PSPI and other products. Among them, polyimide film is currently the world's best performing thin film insulation material, widely used in various fields such as aerospace, microelectronics, atomic energy, electrical insulation, liquid crystal display, membrane separation technology, etc. It, along with carbon fiber and aramid fiber, is considered one of the three major bottleneck key polymer materials that restrict the development of high-tech industries in China. In the low-end PI market, China has basically achieved self-sufficiency; In the high-end field, electronic grade PI films and other products still rely on imports. With technological breakthroughs and capacity upgrades, the scale of China's PI market is expected to further expand, and the market size is expected to reach 24.67 billion yuan by 2027.
High temperature resistant and flame-retardant insulation polyimide PI sleeve
Features: flame retardant, insulation, high temperature resistance, aging resistance, corrosion resistance, low dielectric, good mechanical properties, high stability
Applications: Thermistors, temperature sensors, electric heating elements, electronic probes, high-temperature mirror conduits
Market areas: electric vehicles, batteries, new energy, photovoltaic energy storage, drones, electronic power, communication base stations, smart devices, industrial control equipment, transportation rail, aerospace, etc.